Jack Types


Jack Types: A table showing the differences on the jacks seen so far.

In 2004, After placing some photos here of the jack I found in La Gleize, Per Sonnervik contacted me, pointing out that there was more than one jack type used.
First he showed me some photo's of different types mainly used on Tigers and Panthers, so I got an idea of what was used.
Then he started bombing me with all kind of exceptions he found. At that point I wasn't able anymore to understand what belonged where.
That is where I got the idea of making an identification table for those jacks.
In the mean time, Per bought a 20T jack that I found for sale and allowed me to take it's dimensions before transporting it to Sweden. The resulting drawings, combined with the "La Gleize" museum photos give a good idea how these 20-tonnes jacks functioned and what they look like.
This story continues in 2007 when I was planning a visit to the Saumur Musée des Blindées and was contacted by Ronald Horton to collect a 20TL jack for him. Then I could take it's dimensions and photos. The trip became even more rewarding when I found a rare 15T jack in the Saumur Museum!

It is certain that there are more jack types than the ones mentioned below. Here we only show jack types seen on Panthers and Tigers.

The names used here are not official: We invented them to keep them apart.

10T?
- We don't have much on this one. Per thinks it is probably a 10 ton capacity jack as it looks like the one used on lighter tanks such as the Panzer III and Panzer IV and their variants.
The jack is seen on many Tiger1 line drawings in books (not original drawings), but we found no photo evidence that this jack was really used here. In fact, if it really is a 10T jack, it would be highly unlikely that it was used on heavy tanks like the Tiger1. 
These jacks distinguish themselves clearly from other types by the use of bolts in the body, allowing it to be opened for maintenance.
This jack type seems to be almost unchanged made and in use today in the 1.5T to 20T range. However, we don't know if the range was this complete in WWII.
You can find some modern examples here:
10T Jack type page

15T
- This is a confirmed 15 ton capacity jack. Per found many photos of it. We think it is the 15T jack the books mention to be used on Tiger1, until it was replaced by the sturdier 20TL version. This is also the type mainly used on Panthers, until it was replaced by the 20TL version.
Saumur 15T Jack

20TL
- This is the 20 ton capacity version used on the Tigers. To prevent confusion, we added the "L" - long body - in the name, to prevent it being mistaken with the "S" version. 
Ron's 20TL Jack

20TS
- This is the same 20 ton capacity jack, but here the "S" stands for short body version. There are some advantages compared with the "L" version:
The length is reduced, while it's lifting range remains the same, probably saving a lot of weight, making it better to handle. (Per's jack weighs 60,5Kg. The long version should be around 70Kg)
There is a completely different foot, allowing a more minimized length.
So far we have seen this jack with a crowned top like Per's and a flat top such as in the one in La Gleize.
Per's 20T Jack page
La Gleize "December '44" museum 20T jack

At this point, I think it is necessary to quote Per saying "With these jacks, anything goes!" It means that this table is only to be used as a basic guide. We have seen some photos showing exceptions to the rule. It looks like when a jack was lost or damaged, it could be replaced with anything at hand. Therefore we strongly advise you to check the jack type on the vehicle you want to model with photos if possible. 

In the table below I don't show the swing arms and handle bars to keep a clear view on the jacks. Most jacks are seen with both fixed- and adjustable swing arms and handle bars. However, the 15T jack is only seen with these fixed. 

 

 

10T

15T

20TL - (long)

20TS - (short)

Total
view
jack_files/10t-total.gif jack_files/15t-total.gif jack_files/20tl-total.gif jack_files/20ts-total.gif
Mainly
Used:


Panzer III
Panzer IV
Tiger 1
Panther
Tiger I late
Tiger II
Panther
Also
used
on:

Panther
Tiger I? (no evidence)
  Panther Tiger II
Top
shape


jack_files/10t-top.gif
Straight Pointed Crown
jack_files/15t-top.gif
Straight Pointed Crown
jack_files/20tl-top.gif
Pointed Crown
jack_files/20ts-top.gif
Crown Top or Flat top
Bottom
plate
shape


jack_files/10t-bottom.gif
Square Ribbed
jack_files/15t-bottom.gif
Trapezium
jack_files/20tl-bottom.gif
Square Ribbed
jack_files/20ts-bottom.gif
Square Lowered
Body

jack_files/10t-body.gif
8 Bolts in body
Rivets visible on the other side
jack_files/15t-body.gif
Gear case centered
Rivets in straight line
jack_files/20tl-body.gif
Extended Gear case
Grip strength plates
Curved Rivet Line
jack_files/20ts-body.gif
Extended Gear case
Shortened Body
Axle
plate


jack_files/10t-axles.gif
Nodded axle plate
Gear case around 3 axles
jack_files/15t-axles.gif
Straight axle plate
Gear case around 3 axles
No rivets
jack_files/20tl-axles.gif
Straight axle plate
Gear case around 2 axles
Seen with and without rib
jack_files/20ts-axles.gif
Straight axle plate
Gear case around 2 axles
Seen with and without rib

 

10T - As said before: We don't have much on this one. There are no dimensions available, so these sketches are the result of studying and comparing photos. The rivet and bolt positions should be reasonably accurate, but we have no photo showing the "L" shape lifter at the lower end of the body, so this may look completely different.

10T
Front

10T
Back

Main characteristics of this jack are:

- The gear case is just below the middle of the body and probably, it can be opened for maintenance. The number of rivets on the "back" side suggests that the body consists of three main parts.

- On the thin square ribbed foot, there are four protuberances.

- The rivets at the top and bottom of the body have a different diameter.

- The "Grips" are stuck through holes, then welded on the back side.

- The swing arm (Not shown in the drawings.) is made of one piece.

- The swing arm handle is foldable.

jack_files/10t-total.gif
jack_files/10t-total-back.gif

 

15T - Here also: There are no dimensions available, so the accuracy is about the same as with the 10T.

15T
Front

15T
Back

Main characteristics of this jack are:

- The gear case is placed in the middle of the body.

- The rivets on the lower side of the gear case are placed in a straight line.

- The foot is trapezium shaped, without ribs.

- The front side has a symmetric relatively wide axles plate without visible rivets.

- The back side has an asymmetric axles plate, which is riveted, but has no rivet extensions.

- The "Grip" is stuck through holes, then welded on the back side.

- The swing arm (Not shown in the drawings.) is made of one piece.

- The swing arm handle is not foldable.

jack_files/15t-total.gif jack_files/15t-total-back.gif

 

20TL main differences with the other jacks are:

- A pointed crown top.

- The gear case is placed a little below the middle and is extended to the right side.

Tigers

Panther

Ferdinand

Back

jack_files/20tl-total.gif jack_files/20tlb-total.gif jack_files/20tlf-total.gif jack_files/20tl-total-back.gif

20TL - Tigers:

- This jack has only one "L" shaped grip, which is riveted to the body

- The square foot is seen with a double rib or a single rib (see drawings on the right.)

- The "drop" shaped gear housing fits around two axles. It's left vertical line is tilted a little to the left.

jack_files/20tl-bottom.gif
jack_files/20tl-bottom2.gif

20TL - Panther:

- This jack has two grips, in a different position than the Tigers version. Also the grips are welded directly to the body.

20TL - Ferdinand:

- The "drop" shaped gear housing fits around three axles. It's left vertical line is tilted a little to the right.

- The position of the single grip is the same as on the Tigers version, but on the photos it was impossible to see how it was attached to the body.

- On the photos we saw the foot placed in a square casing.

 

20TS: Of this jack there are many photos and dimensioned drawings placed on these pages:

- Link to Per's Jack page

- Link to La Gleize "December '44" museum photos

Resources:

- "D.W. to Tiger1" by Jentz & Doyle
- "Der Panzer-Kampfwagen Tiger und seine Abarten" by Walter J. Spielberger & Hilary L. Doyle
- "December 1944" museum in La Gleize
- Panzer museum Munster
- Dimensions taken from Per Sonnervik's 20TS jack

 

If you have any comment on this page, please send a mail to: per (remove this and join) (dot) sonnervik (at) telia (dot) com. or contact me via the address specified on the home page